Exp-computer CD Station Manuel d'utilisateur

CD STATIONUSER’S MANUALEXPwww.expnet.com

- 11 -HARDWARE INSTALLATION (PC CARD)Turn OFF your system before connecting the PCMCIA CD-ROM to yourcomputer.1. Connect the PCMCIA interface card to

- 12 -SOFTWARE INSTALLATION (PC CARD)SOFTWARE INSTALLATION FOR WINDOWS 95/98If you are inserting the PCMCIA CD-ROM into your computer for the veryfirs

- 13 -Windows 95 (B)If the Update Device Driver Wizard dialog box appears, as below, itmeans your Windows 95 is version 4.00.950B, i.e. OSR 2.In this

- 14 -Windows 95 (Older Versions)The following dialog will appear. If you are using the PCMCIA CD-ROMunder Windows 95 for the very first time and your

- 15 -Installing 32-bit Card SupportNote: The following procedures apply to the notebook that has install or re-install the original release of the W

- 16 -After the PCMCIA 32-bit Card Support is installed, Windows will ask youto reboot your computer. You should now refer to the previous section for

- 17 -SOFTWARE INSTALLATION FOR WINDOWS NTMake sure of the following before you begin:♦ Windows NT must be version 3.51 or higher.♦Since Windows N

- 18 -Click the Add button, and then click the Have Disk... button. Windows NTwill then prompt you to insert the manufacturer installation disk. Inse

- 19 -SOFTWARE INSTALLATION FOR LINUX (RED HAT DISTRIBUTION)In order to install the PCMCIA CD-ROM, the computer or notebook musthave a PCMCIA package

- 20 -HARDWARE INSTALLATION (OPTIONAL PARALLELPORT)Before you begin, make sure you turn OFF all power to your system beforeconnecting the CD Drive to

- 3 - EXPNon-transferable Limited WarrantyEXP, (EXP Computer Inc. and EXP Memory Products),provides a full one year warranty, from the date ofpurchase

- 21 -SOFTWARE INSTALLATION (OPTIONAL PARALLELPORT)For Windows 95/98Check all the connection as states in the “Hardware Installation” section.From the

- 22 -4. Insert Installation Diskette into the drive selected, Then click OK. If you're installing from a directory containingdownloaded installa

- 23 -Windows NT 4.01. Click on My Computer > Control Panel > SCSI Adapters.2. Choose Drivers tab and the click on Add. From the Install Driver

- 24 -5. Select PHT Parallel-Port PHT-Series NT Driver. Click OK6. Restart the computer when prompted to do so.VERIFY YOUR INSTALLATIONOnce your compu

- 25 -Linux (Red hat distribution)The parallel port CD-ROM IDE modules consist of three parts:4. There is a base paride module required to access the

- 26 -PLAYING AN AUDIO CDUSING THE CD PLAYER UTILITY IN WINDOWS 95/98.1. Connect the 3.5 mm stereo audio cable from the Line-Out Jack of yourCD-ROM t

- 27 -To display the PC card indicator on the task bar, perform the followingsteps:1. Double-click the PC Card (PCMCIA) icon on the Control Panel.2. M

- 28 -HELPFUL HINTSThe following are solutions to some problems that you may encounter whileusing the PCMCIA CD-ROM.IF YOU CANNOT ACCESS A CD-ROMSolut

- 4 -so the above exclusion or limitation may not applyto you.How to contact us:EXP WEB SITE: www.expnet.comTECHNICAL SUPPORT: 516-496-7629TECHNICAL S

- 5 -CONTENTSINTRODUCTION... 7SYSTEM REQUIREMENTS...

- 6 -SOFTWARE INSTALLATION (OPTIONAL PARALLELPORT)... 21Windows 95/98...

- 7 -INTRODUCTIONThe CD Station is a portable external CD-ROM drive, equipped a high-speed PC Card (PCMCIA). The CD station is connected to a PC throu

- 8 -PACKAGE CONTENTSThe items shown below are included in the CD-Station package.1. CD-ROM drive2. AC Adapter Input: 120 VAC Output: 12 VDC 1 Amp.3.

- 9 -PART NAMES AND FUNCTIONSFRONT PANELThe front panel of your CD-ROM may look slightly different from the figureshown below. However, the following

- 10 -REAR PANEL1. Power Button: (Optional in some models)Press the button to manually power on/off the drive when it is poweredby an AC adapter.2. DC